Guide · updated 12 November 2026

How to test battery capacity in mAh with a multimeter

The capacity printed on a battery is a claim. To measure the real figure you have to empty the battery: discharge it through a known resistor, record the voltage until it reaches the cut-off, and add up the current over time. A multimeter, a resistor and a few hours are enough, and the capacity test in TestNMeasure does the recording and the sum for you.

iPhone and iPad (iOS 17 or later): free on the App Store. Android later.

What you need

  • A multimeter on DC volts that can record, or one you are willing to read by hand every 10 seconds.
  • A load resistor of the right value, rated for twice the power it turns into heat: the test runs for hours.
  • Clip leads or a battery holder that hold on their own for hours.
  • A new battery, or a rechargeable cell fully charged and rested.

Never short-circuit a battery, least of all a lithium one. The resistor gets hot: put it on something that does not burn and do not touch it. Do not discharge a cell that is swollen, damaged or hot, and do not leave a lithium cell on the resistor unattended.

Resistor and cut-off per battery

The resistor sets the current, and the cut-off is the voltage under load where the test ends. These are the values the app proposes:

Battery Resistor Cut-off under load Compared with
AA, C and D alkaline 3.9 Ω 0.8 V nothing: the figure only
AAA alkaline 10 Ω 0.8 V nothing: the figure only
9V alkaline 330 Ω 4.8 V a typical 560 mAh (indicative)
AA NiMH 3.9 Ω 1.0 V the capacity on the label
AAA NiMH 10 Ω 1.0 V the capacity on the label
18650 and 21700 Li-ion 10 Ω, rated 5 W or more 3.0 V the capacity on the label
CR123A 100 Ω 2.0 V a typical 1500 mAh

The cut-off is lower than the empty mark of a reading at rest. A NiMH AA counts as empty at rest under 1.20 V, but under load it keeps giving charge down to 1.0 V. Going much further does harm: a rechargeable cell left on the resistor can be damaged, and an alkaline cell can leak.

Alkaline cells have no capacity on the label, because their capacity depends strongly on the load. Measure them to compare batteries with each other, always with the same resistor.

Coin and button cells are rated at a very light load over weeks, so a resistor test gives a much lower figure: test them at rest with the battery checker. For any other battery the usual cut-offs per cell are alkaline 0.8 V, NiMH 1.0 V, Li-ion 3.0 V, LiFePO4 2.5 V, lead-acid 1.75 V (10.5 V for a 12 V battery) and lithium CR cells 2.0 V. A 12 V battery needs a heavier load than a hand-held resistor can carry.

Step by step

  1. Measure the resistor on the ohms range, through the clip leads that will carry the current. Short the probes and press REL first, so the leads read zero. Call the value R.
  2. Set the meter to DC volts and keep the probes on the battery's own terminals, not on the resistor or its clips.
  3. Clip the resistor across the battery and start recording, one reading every 10 seconds.
  4. When the voltage falls below the cut-off, disconnect the resistor at once, then stop the recording.
  5. Open the recording in a spreadsheet, or let the app do the sum.

The arithmetic

The current at each reading is the voltage divided by R. Capacity is that current added up over time, step by step between two readings:

  • mAh: for each step, (the voltage at its start + the voltage at its end) / 2 / R × 1000 × its seconds / 3600. Add up the steps.
  • Wh: for each step, (the start voltage × itself + the end voltage × itself) / 2 / R × its seconds / 3600. Add up the steps.

Stop adding at the first reading under the cut-off. Averaging the two ends of a step counts the falling voltage fairly; using only the first reading of each step counts slightly too much. A shortcut that is close enough for most uses: the average voltage of the run divided by R gives the average current. Multiply it by the hours the run took.

Capacity depends on the load. A battery emptied fast gives less than the same battery emptied slowly, so compare batteries only with the same resistor, and expect a figure under the label when you discharge faster than the maker did.

In the app

Pick the battery in the battery tester and tap Measure capacity. The screen names the resistor and the power rating to use, checks the value you measure through the clip leads, and refuses one that would draw too much current or too little. It shows the cut-off, asks for the capacity on the label where that is the reference, and, when it knows the capacity, estimates how long the test takes. You can save a reading at rest before you clip the resistor on.

Start runs the Battery discharge recording: a reading every 10 seconds, and it goes on when the phone is locked. The screen shows the voltage curve, the mAh and Wh so far and the time. After three readings in a row under the cut-off the recording stops and you get a notice: "Disconnect the resistor now." The app cannot switch the load off, so be there when the test ends.

The result is the capacity in mAh, the energy in Wh, the duration and the average current. With a reference and a complete run it adds the percentage and a verdict: GOOD from 80 %, WEAK from 60 %, REPLACE below. Against the label, REPLACE also says "Far below the label": on a new cell, the usual sign of a fake capacity claim. These limits are indicative: treat them as a guide. A run stopped before the cut-off shows "at least … mAh" without a verdict, and a run with long gaps in the readings is marked approximate.

Already recorded a discharge through a known resistor? Open the session and tap Capacity from this recording, give the resistor and the cut-off, and the app works out the capacity of any battery; type its rated capacity for a verdict. Each result is saved in the recording's session and in the battery history, so you can test the same cell again later and compare. The recording keeps its graph, and the Excel and CSV exports hold every reading with its time.

Where the numbers come from

The resistors and cut-offs follow battery makers' datasheets and handbooks (Energizer for alkaline, NiMH, 9V and CR123A cells) and the IEC test load for an AA cell; the typical 9V figure is read off the maker's chart, so it is marked indicative. The 80 % mark is the usual end of life for a rechargeable cell; 60 % is our own second line. The sums are plain arithmetic on the recording.

What the app does here, and what it doesn't

What it does
What it doesPlan
Measure the mAh and Wh a battery really gives, from a discharge recording through a known resistor.Free
Log sessions hold captures and time-series recordings, and recording continues with the screen locked.Free
Every battery result is kept with the battery, the date and the verdict, so you can see what was tested and how it changed.Free
Review a session as a full graph with pan and zoom, statistics and its captures.Free
Export a log session to Excel with real timestamps and a statistics sheet.Free
Export log sessions and test files as CSV, free.Free

Not yet, or not planned

  • Reads what your meter measures; it doesn't change the meter's accuracy or ranges.
  • One open recording per device; up to 1,000,000 samples per session.
  • Battery results are saved as captures in Records and in the battery history, not as test files with a pass/fail run.

Questions

Can I test battery capacity without discharging it?

No. Voltage shows how charged a battery is now, not how much it can hold. Only a full discharge through a known load measures capacity.

How long does a capacity test take?

As long as the battery lasts at the current you chose: capacity divided by current. A 2500 mAh NiMH AA on 3.9 Ω draws about 300 mA and takes about eight hours. A 9V on 330 Ω takes about a day, and a CR123A on 100 Ω more than two days.

Why is my result lower than the capacity on the label?

The label is measured at a low current, down to a low cut-off. A higher current gives a lower figure, and an old or counterfeit cell gives a much lower one. Test a known good cell with the same resistor to see what your setup reads.

Can I measure the capacity of an 18650 with a multimeter?

Yes. Charge it fully, let it rest, and discharge it through a 10 Ω resistor rated 5 W or more down to 3.0 V. That draws a few hundred milliamps and takes several hours for a typical cell. Stay with it until it ends.

Get TestNMeasure for iPhone and iPad.

iPhone and iPad (iOS 17 or later): free on the App Store. Android later.

Questions or a meter to suggest? Mail support@testnmeasure.app.

No ad networks, no sign-up.