Guide · updated 12 November 2026

Parasitic draw test: find what drains a car battery

A car draws a little current when it is parked: the clock, the alarm, the control units that wait for the key. A parasitic draw test measures that current with the multimeter in series with the battery. The hard part is not the measurement. It is the waiting: a modern car takes many minutes to go to sleep, and until then the reading means nothing.

iPhone and iPad (iOS 17 or later): free on the App Store. Android later.

What you need

  • A multimeter with a 10 A DC range and its fuse intact.
  • Test leads with clips that hold on their own.
  • A charged battery. A healthy car battery reads about 12.60 V at rest when it is full; charge it first if it reads much lower.
  • The key out of the car, all doors closed, the radio code if the car needs one, and time.

Set up the meter before you touch the battery: red lead in the 10 A socket, dial on DC A, 10 A range. With the meter in series, do not crank the engine, do not switch on the ignition, the lights or the blower, and do not open a door. Cranking or a large load through the meter blows its fuse. Opening a door wakes the car and the wait starts again.

Step by step

  1. Switch the car off: engine off, key out, lights off, doors closed. If a door must stay open to reach the battery, press its door switch or latch the lock so the car thinks it is closed.
  2. Set up the meter first: red lead in the 10 A socket, dial on DC A, 10 A range. Always start on the 10 A range.
  3. Put the meter in series: take the negative clamp off the battery post and connect the meter between the post and the clamp with clips, so it stays connected hands-free. Which lead goes on which side does not matter; a minus sign on the reading only shows that the meter is the other way round.
  4. Hands off while it is in series: no cranking, no ignition, no lights, no blower, no doors.
  5. Read the current and wait. Right after you connect, it is high: the control units are still awake. They go to sleep after 10 to 45 minutes, on some cars after more than an hour.
  6. Stay on the 10 A range for the whole test. Do not move the lead to the mA socket: on most meters that breaks the circuit and wakes the car, and the wake-up current can blow the mA fuse.
  7. Read the current when it has stopped falling and holds steady for several minutes. To end, take the meter out, put the clamp back on the post and tighten it. Move the red lead back to the V socket.

What is normal

Current after the car is asleep Verdict
Under 50 mA OK. Normal.
50 to 100 mA BORDERLINE. Some makers allow up to 85 mA on newer cars: check the maker's value.
Over 100 mA FAULT. Something stays awake.

These limits are indicative: treat them as a guide. The 50 mA line is the common workshop rule; the value for your car is in its workshop manual. Wait at least 45 minutes before you call a high reading a fault: until then some control units may still be awake. A current that never settles, but rises and falls again and again, means something wakes up again and again.

Find the circuit

When the current is too high, find the circuit that draws it. Pull one fuse at a time and watch the meter. When the current drops, the draw is on that circuit. Put each fuse back before you pull the next, and give the car time to settle after each change, because pulling and refitting a fuse can wake a control unit.

Why a clamp meter is not enough

A DC clamp is handy for large currents, but its zero drifts by tens of milliamps (an indicative figure; it depends on the clamp). That is more than the 50 mA line you test against, so its reading cannot decide the verdict. Use the meter in series.

The drain test in the app

TestNMeasure has a guided parasitic drain test for a Bluetooth multimeter. Open the battery tester and pick "Parasitic drain" under Guided tests, or tap "Add a drain test" at the end of the car battery test. The app shows the steps above one at a time, in that order: the meter on the 10 A range first, then the negative clamp, then the warnings. It goes on only when the meter reads DC A, and it tells you to use the 10 A socket if the meter reads in mA.

Then tap "Start the log", close the car and walk away. The app records the current as an ordinary recording, also with the phone locked, and draws the curve with the 50 mA and 100 mA lines. The state line reads "Waiting for the car to fall asleep" until the current has held steady for five minutes, then "Asleep after 13:00 · 32 mA", with the time and the current of your car. The steady-window rule is our own and indicative.

The result is the sleep current with the verdict OK, BORDERLINE or FAULT, and the note "Indicative limit: treat it as a guide." FAULT is only called after 45 minutes. After an hour without a steady reading the app says "The current keeps changing: something wakes up again and again." and gives no verdict. With a DC clamp meter it shows the numbers only and recommends the series method.

"Save result" stores the sleep current, the time to fall asleep and the verdict in the battery history, next to the battery's other results, where the Drain filter finds it again. Started from the car battery test, the drain result and its curve also go into that test's one-page report. "Open recording" shows the whole curve with pan and zoom, so you see the current fall in steps as each control unit goes to sleep. While you pull fuses, the live graph shows each drop as it happens.

Where the numbers come from

The limits and the sleep times are common workshop values from meter makers' application notes on the parasitic drain test. The 85 mA allowance differs by car and maker, and the five-minute steady window is our own rule: both are marked indicative until we have checked them on more cars. A resting voltage tells you how charged the battery is, not what drains it, and not whether it can still carry the starter's load; for that, see the car battery voltage chart. Your car's workshop manual has the maker's own limit.

What the app does here, and what it doesn't

What it does
What it doesPlan
Log the current a switched-off car draws while its control units fall asleep, against the 50 mA line.Free
Every battery result is kept with the battery, the date and the verdict, so you can see what was tested and how it changed.Free
A guided test of a 12 V starter battery and its charging system: rest, cranking, charging and ripple, with a one-page report.Free
Log sessions hold captures and time-series recordings, and recording continues with the screen locked.Free
Review a session as a full graph with pan and zoom, statistics and its captures.Free
Swipe the readout to a live graph with min and max lines, pan and zoom.Free

Not yet, or not planned

  • Reads what your meter measures; it doesn't change the meter's accuracy or ranges.
  • One open recording per device; up to 1,000,000 samples per session.

Questions

How much parasitic draw is normal?

Under 50 mA once the car is asleep. Between 50 and 100 mA is borderline, and over 100 mA is too much: something in the car stays awake. These limits are indicative; some makers allow up to 85 mA on newer cars.

How long does a car take to go to sleep?

Usually 10 to 45 minutes after you switch it off and close it, and on some cars more than an hour. Every opened door starts the wait again, which is why the test is done with the doors closed and the key away from the car.

Should I switch to the mA range for a better reading?

No. Stay on the 10 A range for the whole test. Moving the lead to the mA socket breaks the circuit on most meters, which wakes the car, and the wake-up current can blow the mA fuse.

Can I do a parasitic draw test with a clamp meter?

Not reliably. A DC clamp drifts by tens of milliamps, and the limit you test against is 50 mA. Put a multimeter in series with the battery instead.

Get TestNMeasure for iPhone and iPad.

iPhone and iPad (iOS 17 or later): free on the App Store. Android later.

Questions or a meter to suggest? Mail support@testnmeasure.app.

No ad networks, no sign-up.